Just How to Install a Bathtub: Set Up an Acrylic Bathtub and Bathtub Surround
Just How to Install a Bathtub: Set Up an Acrylic Bathtub and Bathtub Surround
Blog Article
Listed here in the next paragraph you can find some first-rate insights about A Step-by-Step Guide to Installing a Bathtub.
Installing a tub isn't precisely brain surgery, yet it does call for strong plumbing, woodworking, and also occasionally, tiling abilities. Changing an old bathtub with a brand-new one is additionally a reasonably difficult project. If the old tub is readily available, the project can move rapidly; if you need to open up a wall surface to get rid of the old bathtub and also place the brand-new bath tub, the job is a lot harder. In either instance, the job is within a house handyman's abilities, although you will need a helper to leave the old tub as well as set in the new one. Ensure you have qualified on your own for the work and also fit trying it. As opposed to working with a specialist to take over a halfway-completed project, it is better to consider using one prior to you start. Possibilities are you may need a professional plumber to make tube links.
This write-up will certainly assist you set up a new bathtub in your bathroom if you have actually currently purchased a brand-new bathtub as well as don't need to change the setup of your previous water pipelines.
Your tools and product list must comprise the following:
Planning for the Installation
Firstly, the sustaining framework supplied with the bathroom must be fitted (if needed) according to the producer's guidelines. Next off, fit the taps or mixer to the bathtub. When suitable the tap block, it is important to see to it that if the tap comes with a plastic washing machine, it is fitted between the bath and also the taps. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the taps unit to stop stress on the bath tub.
Fit the versatile tap adapters to the bottom of the two faucets utilizing 2 nuts and olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet through the hole in the bathroom. Use the nut provided by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Ensure you make use of every one of the supplied washing machines.
Connect the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bath must now prepare to be fitted in its last position.
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your setup, after that the first thing you should do is detach the water. After doing so, turn on the faucets to drain pipes any water staying in the system. The procedure of removing the existing faucets can be fairly problematic because of the limited access that is frequently the situation.
Make use of a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipes to the faucets. Have a towel ready for the staying water that will certainly originate from the pipes. When the supply pipelines have actually been removed, utilize the exact same device to loosen the nut that holds the taps onto the bath/basin. You will require to quit the single taps from turning throughout this procedure. As soon as the taps have been eliminated, the holes in the bath/basin will certainly need to be cleansed of any old sealing compound.
Prior to going on to fit the brand-new faucets, compare the pipe connections on the old taps to the new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is required for the new taps to fit.
Setting up the Tub
Utilizing both wood boards under its feet, position the bath tub in the required position. The wooden boards are useful in evenly spreading the weight of the tub over the area of the boards rather than concentrating all the weight onto 4 little factors.
The following objective is to make certain that the bath tub is leveled all round. This can be attained by examining the level and also readjusting the feet on the bath tub till the level reviews degree.
To mount faucets, fit all-time low of the outermost adaptable faucet adapter to the proper supply pipeline by making a compression sign up with; after that do the exact same for the other tap.
Switch on the supply of water and check all joints and new pipework for leakages and also tighten them if essential. Load the tub and likewise check the overflow outlet and the regular electrical outlet for leakages.
Lastly, repair the bath paneling as defined in the supplier's instruction manual. Tiling and sealing around the bathtub should wait until the bath tub has actually been made use of at the very least when as this will settle it into its final position.
Fitting New Touches
If the tails of the brand-new faucets are plastic, after that you will need a plastic connector to prevent damage to the string. One end of the adapter fits on the plastic tail of the faucet as well as the other end offers a connection to the current supply pipelines.
If you require to fit a monobloc, then you will require reducing couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next, position the faucet in the installing hole in the bath/basin making certain that the washing machines are in area in between the tap and also the sink. Protect the tap in position with the producer provided backnut. When the tap is firmly in place, the supply pipes can be linked to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with typical tap adapters. The former kind ought to be connected to the faucet ends initially, tightening just by hand. The supply pipes can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Bathtub
In the area where the bathroom satisfies the tile, it is essential to seal the joins with a silicone rubber caulking. This is necessary as the fitting can relocate enough to crack an inflexible seal, triggering the water to pass through the wall surface between the bathroom and the tiling, bring about issues with dampness and also possible leakages to the ceiling below.
You can pick from a range of coloured sealers to blend in your components as well as fittings. They are offered in tubes and cartridges, as well as are capable of securing gaps as much as a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can fill it with twists of drenched paper or soft rope. Remember to constantly load the bathtub with water prior to securing, to allow for the motion experienced when the bathtub is in use. The sealer can crack relatively very early if you do not take into account this movement prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are likewise conveniently readily available on the market. It is a good idea to fit the floor tiles making use of water-resistant or water resistant glue and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a serious reader about Tools You Need to Install a New Bathtub , I figured sharing that piece of writing was a good thing. Appreciated our write-up? Please share it. Let somebody else discover it. We truly appreciate reading our article about How to Install a Bathtub.
Get Quote Now
Report this page